Allplan bridge 2021
Parametric bridge model with Allplan Bridge Thus, they decided to switch to Allplan Bridge during the ongoing project.
#Allplan bridge 2021 software#
The engineers soon realized that the software they were using was not up to the complexity of the task and that too much time would have to be invested in modeling. The alignment axes in particular posed an enormous challenge, as they differed in the two directional lanes and required, among other things, a complicated cross-section widening of the RF Dortmund. Once the preferred variant had been decided, it still had to be modeled. The individual spans of the foreshore bridge vary between span widths of 25.8 and 56 meters. Preference was given to a variant consisting of a tied arch bridge with a span of 68.0 m in the area of the canal crossing and a subsequent foreshore bridge as a two-span plate girder with two integral support axes and variable headroom. The engineers calculated a total of nine variants, in each of which the structure was separated into a canal bridge and a foreshore bridge. The client, the Lower Saxony State Authority for Road Construction and Traffic (NLStBV), commissioned THORMÄHLEN + PEUCKERT with a variant investigation in the course of the preliminary planning as well as with the modeling of the preferred variant for the construction of the new replacement. Preferred variant: Canal and foreshore bridge According to the expert opinion, the target load level could only be achieved by a new replacement structure. A structural analysis showed that the bridge does not have sufficient load-bearing capacity in the longitudinal and transverse directions. The 261.5-meter-long structure crosses the Osnabrück branch canal including service road and embankment section, the Hase watercourse as well as unpaved areas in the floodplain and a service road with adjacent ditch. This expansion in six construction phases includes a seven-span bridge built in 1969 between the Osnabrück Nord and Osnabrück Hafen junctions. Replacement for seven-span bridge from 1969ĭue to the high volume of traffic, the A1 highway between the Ahlhorner Heide interchange and the Lotte/Osnabrück interchange has been widened from four to six lanes for several years. In the Lower Saxony BIM pilot project "Highway A1: Replacement of the bridge over the Hase and the Stichkanal" near Osnabrück, the modeling software was replaced by Allplan Bridge in the middle of the project. This sometimes also involves choosing the right software. As part of the efforts of the federal and state governments to promote digital design and construction, a large number of infrastructure projects are currently being carried out in which the foundations for the application of BIM are being developed.
It's about finding out what works and what doesn't. This is not only one of the most important foundations for success in general, but also one of the core principles of pilot projects. We will fix the problem ASAP.When a BIM pilot project in Lower Saxony became too demanding for their modeling software, THORMÄHLEN + PEUCKERT successfully switched to Allplan Bridge. This is only a temporary solution to bypass the error message, so that you can still use VS. The new file should be placed unter the same folder, where the Slider_deu.xml is located. E.g., Slider_ eng.xml for English version or Slider_ ita.xml for Italian Version, etc. A quick fix/workaround is to duplicate the Slider_ deu.xml (the German translation file), and to rename the new duplicated file based on the language you use. It is caused by some missing translation file for nodes slider. It happens if VS isn't started in the German version of Allplan. An example of the error message looks like:įailed loading file FilePath\Filename.pyp.Įrror message: Could not find text with ID=1222 in C:\ProgramData\Nemetschek\Allplan\2021\Etc\VisualScripts\InputControls\Slider\Slider_eng.xml.Įxception message: Could not find text with ID=1222 in C:\ProgramData\Nemetschek\Allplan\2021\Etc\VisualScripts\InputControls\Slider\Slider_eng.xml.
#Allplan bridge 2021 update#
We just noticed that with the new update installed you may get following error message, if you try to open any existing script with VS.